Double Glazed Window Repairs
If your double-glazed windows start to fog up, it could be an indication that the seals are not working properly. This could affect the thermal performance of your home and should be addressed as soon as you can.
You can lubricate the hinges, handles and mechanism to see if it helps. It is best to let an expert fix it to ensure it is done right.
Broken Panes
Chips and cracks on your window's glass can be a hassle, but they aren't necessarily permanent. Repairing a damaged pane with some patience and some basic tools, which are likely to be in your home.
click home page to leave the work up to a professional if your window has a large crack or is within an old wooden frame. If your window is double-paned, it may be difficult to find a replacement exactly the same size as your previous one.
When replacing a window, the first step is to take the old pane from the sash. Wear safety goggles and tape the sash in a cross-hatch design using duct tape. This will prevent glass shards from falling off while you work. Tap the sash using an abrasive tool with an elongated tip or hammer in order to loosen up the putty. If your window has wooden mouldings to hold the pane in place, you can carefully pry these pieces off with a flat prybar if it is framed in wood.
When the old window is removed, clean and prepare the space to be used for a new one. Utilize a wire bristle broom to smooth out the grooved channel in which the window will be installed. Clean any remaining putty or sash. The old putty can be heated with the aid of a heat gun, making it easier to remove.
Subtract 1/16 inch each from the width and length of the sash. This will ensure that the replacement pane is slightly bigger than the opening, so that it can expand or expand in response to temperature fluctuations. Roll a rope of glazed putty around the new pane's perimeter, then press it into the grooved channels of the frame. Put a glazier's point into every corner of the new pane, and at about 6 inches intervals across the frame.
A damaged double or triple paned window could let hot or cold air to escape, which could cause your HVAC system work harder to maintain an indoor temperature that is comfortable. They are also insulated by gas fills which means that if you damage them your home won't be as well-insulated.
Draughts
Double glazing is designed to be tough, secure and hard-wearing However, it can suffer from issues as a result of normal wear and tear. Draughts are a common problem that can be both bothersome and costly. Draughts are caused by the gap between windows and a wall, or between the window sash frame. This gap allows cold air to enter the house and warm air to escape, resulting in higher energy bills.
There are a variety of ways to fix drafty windows. One method is using mortite caulk, also known as temporary caulking. These products are available in rolls or tubes and can be sprayed on the gaps. Then, they can be painted to match the window you have. This makes them nearly invisible. Another option is to purchase a draught-proofing kit. This usually includes plastic sheeting which you stick to the window using tape, and then heat with a hairdryer, sealing the gaps to keep cold air out.
You can also eliminate the draughts by installing a new window lock or by enhancing the hinges of your uPVC Windows. To determine if the window hinges are damaged test sliding a small piece of card between the frame and sash. If you're able to move the card with ease, your window hinges may need to be replaced.
You can purchase draught-proofing strips to fit around the frame of a tilt-and-turn or casement window. These are available in metal, foam or plastic. Some of them have self-adhesive backing, while others require to be pinned into place. Brush strips are available for sash windows, which fit into the gap and block out draughts. These strips are similar to those found on front doors.
It is essential to have your double-glazed windows fixed by a professional when you spot any issues, as leaving them unattended could cause more damage and a decrease in effectiveness. You can find a local tradesman who can perform repairs to double-glazed windows using the search function of this site. Our traders have all been screened and checked so you can be sure that you will receive a high-quality service.
Smudging
Installing double-glazed windows at home or in the office is a great method to keep cold air out in winter and hot air out in summer. They also provide a great soundproofing barrier, which helps to block out noise from the outside world. As with all windows however, they'll become worn out and will require some attention. It's good to be aware that double-glazed windows can be repaired rather than replaced.
One of the most frequent repair jobs on double glazed windows is to repair the sash cords which hold weights that balance that allow you to open and close your window. Repairing the damaged sash cable will vary based on your window's size and complexity. On an average, you will need to pay around $200 for this service.
Fogging is usually caused by the accumulation of moisture between the window panes. A technician will need to make a small hole in the glass, and then use a chemical solution to remove the water. The process is about $150, but it can be more than doubled in the event that the frame is decaying.
Another option to fix a foggy double-glazed window is to defog the glass from the inside out. This is a less expensive option than replacing the IGUs but it will not return the R-value of windows back to their original levels.
Smudging has been a ritual in many cultures to cleanse areas of negative energy and promote positive energy. Using a smudge stick with the herb sage or other can help eliminate pollen, mold and germs. spores, which will improve allergies and asthma symptoms for those affected by them. It can also be used to get rid of lingering odors and energy from objects like antiques and modern furniture. It is recommended that you smudge your house at least four times per year and whenever you feel that negative energies are hanging around or in the space.
Replacement
Over time, double-glazed windows (or sealed units as they are also known) can fail, in particular the airtight seal that holds the inert Argon gas in and prevents condensation between the glass panes. In this instance, it may be necessary to replace the unit. It is not as hard as it might seem. A competent DIYer can put together a high-quality unit in a short amount of time.
With a utility knife or putty knife, remove any glazing points that hold the existing unit. After the glazing points are removed, the installer can cut and slice the sealant that is securing the unit. This is usually done with a bladed tool such as a jigsaw or a knife. After the old IGU is removed and replaced with a new one, it can then be inserted into the frame and the gap sealed with silicone sealant.
After the silicone is applied and dried, a small amount of paint can be used on any silicone that is exposed to make the new windows look like new. Reattaching handles to the frame is the next step. A final inspection is conducted to ensure that everything is in order before the FENSA authorized contractor leaves your property.
As well as fixing double-glazed windows, our glaziers can also install replacement windows for those that would like to upgrade their home with the latest energy saving advances such as argon gas-filled glass and thermal spacer bars. These improvements can reduce the cost of heating and ensure your home is at a perfect temperature all year round.
If your double-glazed windows are showing signs of wear, you should consider contacting us immediately to request repairs or replacement. This will not only enhance the appearance of your house but could also increase the value when you decide to sell it.